Portfolio
Our Work
Selected projects from the workshop, documented from the first cut to the final install.
Restaurant & Commercial Seating
Bar Lucy — Custom Banquette Seating
A full banquette build for Bar Lucy, a neighborhood Italian restaurant on Long Island. Thirty linear feet of curved L-shaped seating, fabricated in sections at the workshop and installed to the room's exact dimensions.
Custom hardwood frames assembled in sections — each unit built to the restaurant's exact architectural drawings, with leveling feet for precise on-site installation.
Eight-way hand-tied coil springs on every seat section — the same standard used in high-end residential furniture, applied here for a seat that holds its shape through daily commercial use.
Channel tufting completed — clean vertical lines across the full curved span, fabric tensioned uniformly before the sections leave the shop.
The inside corner — continuous vinyl pulled tight with clean architectural lines at the junction, no visible seams where sections meet.
Laser-level alignment during the workshop dry-fit — all sections calibrated for consistent height, depth, and seam alignment before delivery to the restaurant.
Red vinyl seating running the full length of the dining room and bar. Built to the designer's specification, fitted to the room.
Scope
30 linear feet of L-shaped banquette seating, fabricated in five sections and delivered ready to install
Construction
Eight-way hand-tied coil springs throughout — built for high-volume daily use in a hospitality setting
Material
Contract-grade vinyl in the signature red specified by the restaurant's design team — chosen for durability and ease of cleaning
Working on something similar?
Discuss Your ProjectMarine, Auto & Aviation Work
Sportfish Center Console — Full Re-Upholstery
A full re-upholstery of a center console sportfish boat — every seat, cushion, and backrest replaced in marine-grade vinyl. Panels cut to the hull, built for the Long Island Sound.
Original vinyl across all seating positions — sun-faded, cracked at the wear points, and no longer serviceable. The full interior needed to be stripped and rebuilt.
Bow cushion and backrest re-done in light gray marine vinyl — cut to the hull's contour, edge-stitched, and fitted without gaps.
Rear bench and backrest re-upholstered as a matched set — consistent panel lines and tight edge stitching across the full width.
Leaning post bolster and aft seat cushion — both re-upholstered to the same specification as the forward sections, maintaining consistent material and finish across the entire boat.
The completed boat at the dock — all seating positions re-done, the interior unified in a single clean material throughout.
Scope
Full interior re-upholstery — bow seating, cockpit bench, leaning post bolster, and stern seat — all positions replaced in a single service
Construction
Precision-cut panels custom-fitted to each seat housing — no standard sizing, every piece patterned to the boat's exact dimensions and mounting hardware
Material
Marine-grade vinyl — UV-stabilized, mildew-resistant, and salt-tolerant, specified for Long Island coastal use and matched across all positions
Recent Project · Aviation
Custom Aircraft Interior Upholstery
Blue-and-gray upholstered seating gives this aircraft a distinctive, coordinated look from the cockpit to the rear cabin. Explore the seating details and the aircraft itself below.
Have a boat or outdoor space that needs work?
Contact UsResidential Upholstery
Built-In Corner Banquette
A fully custom built-in — from raw plywood fabrication through finished installation. Sage velvet upholstery, hand-shaped scalloped backboard, twisted rope piping, and cream fringe trim throughout.
Custom plywood frame constructed in place — the scalloped arch silhouette cut and fitted before any fabric is touched.
Upholstered L-corner with continuous rope piping trim and pleated fringe skirting along the base.
Full L-shaped banquette installed — sage velvet spanning the entire frame, fringe trim level from wall to wall.
Twisted rope cord follows every curve of the shaped backboard — hand-applied and pulled tight at each inset radius.
Fabrication
Custom plywood frame built in-place — scalloped arch profile shaped before upholstery begins
Materials
Sage velvet, twisted rope piping, cream tassel fringe — all applied in continuous runs with no visible seams
Scope
Full L-shaped built-in — backboard, seat, apron, and skirting all upholstered to a finished edge
Antique & Custom Furniture Restoration
Antique & Custom Furniture Restoration
Sofas, sectionals, and specialty pieces — each one stripped to its frame, rebuilt structurally, and reupholstered from scratch. Three projects documenting the full scope of residential furniture restoration at the shop.
Parsons Sofa — Complete Rebuild
The frame suspended on sawhorses — foam pad, cotton batting, and burlap laid in sequence before any fabric is cut.
Three-seat parsons profile in warm champagne woven — tight-backed, fully upholstered platform base, no exposed leg.
The arm profile and fully upholstered side panel — fabric pulled taut and knife-edged at every seam.
Mid-Century Sectional — Full Re-Upholstery
The piece as received — original white button-tufted fabric worn through to the foam, frame sound but upholstery well past its useful life.
The walnut platform base fully exposed — L-shaped frame inspected, joinery checked and reinforced before any new material is applied.
The completed piece — light gray wool-blend over the full L form, button tufting restored to period pattern, original brass casters polished and retained.
The low platform profile — walnut edge crisp, fabric pulled flat across the full seat depth, tufts uniformly spaced.
The full L from above — button grid precise across both sections, corner join clean, walnut frame visible at every edge.
Ikat X-Frame Stools
Frame stripped bare — original fabric removed, X-base exposed and ready for new construction.
Single stool completed — the ikat pattern carries continuously across the seat top and all four sides of the X-frame.
Both stools finished and matched — identical pattern placement on every surface, front to back.
Approach
Every piece stripped to bare frame before any new material is applied — foam, batting, and spring systems rebuilt from scratch on each project
Scope
Residential sofas, antique sectionals, and specialty accent pieces — full rebuilds and complete re-upholstery commissions
Materials
Champagne woven, light gray wool-blend, bold ikat stripe — fabric selected to suit each piece's period, silhouette, and use
Custom Upholstered Bed Frames
Custom Upholstered Bed — Built from Frame
A full custom build — platform base and oversized winged headboard constructed from raw wood, then upholstered entirely in cream linen with deep button tufting throughout. No kit, no shortcuts. Built and finished in-shop from the first cut of lumber.
Platform base and full-height winged headboard built from raw lumber — every joint set before a single piece of fabric is touched.
Delivered and set in place — headboard fully upholstered in cream linen with deep button tufting, platform base wrapped clean to the floor.
The completed piece — tufting grid precise across the full headboard face and wing panels, every seam sharp, fabric pulled flush to the base.
Scope
Full custom build — frame carpentry and complete upholstery executed in-house from raw material to finished piece
Construction
Platform base with integrated wood frame, oversized winged headboard, deep button tufting set across all upholstered surfaces
Material
Cream linen throughout — headboard face, wings, side rails, and platform base wrapped in matching fabric for a unified profile
Fabric Ceilings & Wall Upholstery
Fabric Ceiling & Wall Upholstery
A complete residential bedroom transformation — every wall surface fabric-wrapped, and the entire ceiling hand-pleated into a radial sunburst pattern radiating from a single center point. One of the most technically demanding installations in the portfolio.
Full-room installation underway — walls prepped and fabric staged for ceiling tensioning and pleating.
Each pleat radiates outward from the center medallion — hundreds of folds tensioned and secured by hand.
The ceiling spans the full room — the pleating runs wall to wall without interruption, accommodating the vaulted angle.
Technique
Radial hand-pleating from a single center point — each fold tensioned individually across a full ceiling span
Scope
Full room coverage — all four walls fabric-wrapped, ceiling pleated, plus a custom-upholstered mirror surround
Material
Woven natural-tone fabric with consistent texture across all surfaces — ceiling, walls, and trim treated as one continuous installation
Begin Your Project
Let's build something together.
Every project is quoted personally from our Bellport workshop — no commitment required.